Accusplit Watch AE520S User Manual

LCDTimer/Stopwatch/Clock  
AE520S  
Operating Instructions  
SETUP  
The unit operates on one ‘C’ size R14 battery that has a life expectancy in excess of one year.  
Remove the battery cover and fit the R14 battery into the correct position. Replace the battery cover.  
INTRODUCTION  
ACCUSPLIT products use a common setting procedure called S1-2-3-4.  
S1 = enter the setting mode  
S2 = change the field to be set  
S3 = change the field value(s)  
S4 = exit the setting mode  
TO SET CLOCK AND DATE  
S1 - Slide the switch to the CLOCK SET (labeled as “SET”) position.  
S3 -To set the time, press and hold the hour and minute buttons separately to fast forward to the correct  
time. Press the second button to zero the second display.  
S3 -To change between 12 and 24 displays, press the SPLIT/RESET button.  
S2 -To set the date display, press the START/STOP button to alter the display.  
S3 -To adjust the day, date and month, press the HOUR, MINUTE & SECOND BUTTONS respectively.  
TO SET ALARM  
S2 - Slide the switch to the ALARM (ringing alarm clock icon) position.  
S3 - Set the alarm by pressing the HOUR & MINUTE buttons.  
Turn the alarm function on by pressing the CLEAR button.The alarm sign will show on the left of the display.  
To turn the alarm sound off, press either of the top buttons.  
To turn the alarm function off, with the slide switch at ALARM, press the CLEAR button.  
TO OPERATE STOPWATCH  
Slide the switch to the Stopwatch icon (COUNT UP) position.  
There are four modes of count up that are selectable, which can be changed by pressing the HOUR button.  
STW  
1 second to 23 hours, 59 minutes, 59 seconds.  
1/100 second to 59 minutes, 59.99 seconds  
1/100 second to 9999.99 seconds  
STW + 1/100s  
STW + DS  
STW + DM  
1/100 minute to 1999.99 minutes  
The count up function operates using the START/STOP buttons with a lap option by pressing the  
SPLIT/RESET button. When the lap is being held the display shows SPL above the seconds display.To  
restart the count up after the lap time has been noted, press the SPLIT/RESET button.To stop and set  
the time back to zero, press the START/STOP button and then the RESET button.  
TO OPERATE MEMORYTIMER  
S2 - Slide the switch to the hourglass icon (TIMER) position.  
S3 - Press the HOUR MINUTE & SECOND buttons to set the time period required. If an error in setting  
occurs, press the RESET button and start again.The memory facility will display MEM on the right of the  
display, after setting the unit and before pressing the START button. When the set time has elapsed an  
alarm will sound, which is turned off by pressing the STOP button. After the alarm has sounded, the  
display will count up the time taken to turn off the alarm. After the STOP button has been pressed at the  
end of the count down period, the last timing period that is stored in the memory is displayed.  
The timing period can be stopped (”Time Out”) and re-started (”Time In”) by pressing the START/STOP button.  
REGISTER NOW Please return  
your AE520S Registration to the  
Repair Center address in the  
warranty, and we will let you  
know about future products.  
Email (preferred)  
User  
NO-PROOF-OF-PURCHASE LIMITEDWARRANTY  
See label on back of unit for details, or check  
ACCUSPLIT, Inc. • 3090 Independence Drive, Suite 148 • Livermore, CA 94551 USA  
800-935-1996 • 925-290-1900 • FAX 925-290-1930 • www.ACCUSPLIT.com • support@ACCUSPLIT.com  
970-030  
 

3Com Dishwasher 61 362 User Manual
Acer Computer Monitor B243W User Manual
Agilent Technologies Electronic Accessory U1251A User Manual
Aiphone Intercom System AN 8000EX User Manual
Aiwa Car Satellite TV System TV 1402 User Manual
American DJ DJ Equipment Dyno Fog User Manual
Axis Communications Webcam Q7424 R User Manual
Barco Computer Monitor MIVD 1218 User Manual
Beckett Water Gardening Outdoor Fountain CGFK60 User Manual
Behringer Car Speaker b1030 User Manual